风口生产厂家逸捷主营:浙江防火阀加工,风口厂家批发,防火阀厂家直销,防火阀厂家,多叶送风口价格,混流风机生产厂家等!

咨询热线:

0571-85460486

行业新闻
当前位置:网站首页 > 新闻中心 > 行业新闻
  • 做好铝合金风口规格尺寸合格检查
  • 本站编辑:杭州逸捷暖通设备有限公司发布日期:2019-12-22 13:50 浏览次数:

铝合金风口具有正压的空调房间自动排气,通常情况下靠风口的百叶自重而自然下垂,阻隔室表里的空气交流,当室内气压大于室外气压时,气流将百叶吹开而向外排气,反之室内气压小于室外气压时,气流不能反向流入室内,该风口有单向止回作用。

  孔板送风时,风速均匀而较小,区域温差也很小。因此,对于区域温差和作业区风速要求严格、单位面积送风量比较大、室温允许波动规划较小的有恒温及净化要求高的空调房间,宜选用孔板送风的方法,单层百叶风口的风口气流调理方向是一维的,不是水平左右就是垂直上下这两个方向之一,但双层百叶风口的风口气流调理方向是二维的,具有水平左右和垂直上下两个方向。

  铝合金风口常用于管道中的吸、送风用,促销单层百叶风口规格尺度同时可根据实际情况配上人字闸(多叶对开调理阀),用以操控风量或安装铝合金过滤器,进行配套使用。叶片可分为横放和竖放两种,可灵活的左右或许上下滚动,以操控气流方向。

  风口时要考虑空调表里区的差异。内区房间空调负荷较小且改变崎岖不大,空调作用简略到达,为了协作建筑装修规划,空调内区房间气流组织可以比空调外区房间稍差一些。铝合金风口的窄边总宽度仅为150 mm或200mm,折边很小,吊顶开洞尺度有必要准确。规划条缝型风口时应防止超长,超长的条缝型风口都是一节一节连接起来的。

1480494679101567.jpg

Aluminum alloy tuyere has positive pressure air-conditioning room automatic exhaust, usually by the self weight of the louver of the tuyere and natural droop, blocking the air exchange in the table of the room, when the indoor air pressure is greater than the outdoor air pressure, the air flow will blow the louver open and exhaust outwards, on the contrary, when the indoor air pressure is less than the outdoor air pressure, the air flow cannot flow into the room in reverse, the tuyere has a one-way check effect.

When the orifice plate is used for air supply, the wind speed is uniform and small, and the regional temperature difference is also small. Therefore, for air-conditioned rooms with strict requirements for regional temperature difference and wind speed in the operation area, large air supply volume per unit area, small room temperature allowable fluctuation planning, and high requirements for constant temperature and purification, orifice air supply method should be selected. The air conditioning direction of the single-layer louver is one-dimensional, either horizontal left-right or vertical up-down, but the air conditioning direction of the double-layer louver The air conditioning direction of tuyere is two-dimensional, with horizontal left and right and vertical up and down two directions.

Aluminum alloy tuyere is commonly used for air suction and supply in the pipeline. The specification and scale of single-layer louver tuyere can be promoted. At the same time, herringbone gate (multi leaf split regulating valve) can be equipped according to the actual situation to control the air volume or install aluminum alloy filter for supporting use. The blade can be divided into two types: horizontal and vertical. It can flexibly roll left and right or up and down to control the air flow direction.

When the air outlet, the difference between the inside and outside of the air conditioner should be considered. The air conditioning load of the inner room is small and the change is not big. The air conditioning effect is simple. In order to cooperate with the architectural decoration planning, the air distribution of the inner room of the air conditioning can be slightly worse than that of the outer room of the air conditioning. The total width of the narrow edge of the aluminum alloy tuyere is only 150 mm or 200 mm, and the folding edge is very small, so it is necessary to accurately size the opening of the ceiling. When planning the slot type air vent, it should be prevented from being too long. The extra long slot type air vents are connected one by one.